Details

Details

In many cases, stock wheel bearing nuts and star washers can be used several times. However, with the increased maintenance required of an off road vehicle, these will need to be replaced. Trail-Gear now offers a Chromo Spindle Nut Kit that allows you to more easily service your axle and decreases your long term service costs. The Locking Nut and Washer have been CNC machined from 4130 Chromoly. The Nut has also been heat treated to Grade 8 standards. Kit comes with the hardware necessary for one axle.

Advantages over stock:

• Stronger than stock. Made out of 4130 Chromoly.
• Extends the life of your wheel bearings due to loose spindle nut and OEM lock washer.
• Ease of installation.

This kit includes:

• Thrust Washer (qty 2)
• Spindle Locking Nut (qty2)
• Spindle Locking Washer (qty 2)
• Washer, M3 locking (qty 4)
• M3-.05 Socket Head Cap Screw (qty 4)

NOTE: 1 KIT SERVICES 1 FULL AXLE

These bolt on wheel spacers are designed to give you a little more width without changing out your axle for a wider one. Great for use on solid axles conversions to make the front axle similar in width the wider rear axle found on 86 and up Toyota trucks. Bolt pattern is 6 stud on a 5.5" round circle. Features safety graded studs and matching nuts for proper fit. Made from Billet 6061-T6 aluminum. Grade 8 Studs, Grade 10.9 nuts. Five sizes available. Shipped as a set of 2 spacers w/nuts. Every spacer features a precision machined surface. Only high quality nuts and studs that are hardness graded and stamped are used. Six lug wheel spacers fit Toyota Pickups, 4Runners, FJ-40, FJ-60 & FJ80

This is for a PAIR of spacers

Long travel shocks are an important part of a flexible off road suspension system. Bilstein shocks are world renown for quality and performance.

All shocks sold include sleeves for both top and bottom bolts.

Eye sleeves are 1/2" ID (12.7mm)

Dimensions are eye to eye

Bilstein 8" 5125 (v255/70) Shocks (33-185590) Ext 21.5" (546mm) Col 13.5" (343mm) travel 203mm

Bilstein 10" 5125 (v255/70) Shocks 33-185552 10" travel Ext 25.93" (659mm) Col 15.91" (404mm) travel 255mm

Bilstein 12" 5125 (v255/70) Shocks 33-185569  12" travel Ext 29.7" (754mm) Col 17.91" (455mm) travel 299mm

Bilstein 14" 5125 (v255/70) Shocks 33-185576  14" travel Ext 34.9" (886mm) Col 20.75" (527mm) travel 359mm

Anyone who has dual cases with 4.70 gears in their Toyota rock crawler has at one time or another broken an OEM rubber motor mount and heard the awful sound of their fan blades hitting their radiator. We have an answer for that problem, we call it the Bomb Proof Motor Mount Kit. We feel so confident about this product that we back it up with a world famous No Questions Asked Lifetime Warranty.

The base of the motor mount (frame side) is made out of 1/4 inch plate, while the surface plate that the motor sits on is made out of 3/8 inch material and has a class 10.9 bolt that is mechanically locked to the engine mount plate, not just threaded in. The bushings out of a high grade polyurethane for durability and years of dependability. The finish is a clear zinc plating that looks sharp and will last a lifetime. The mount holes are slotted so that the Bomb Proof Motor Mount Kit is easy to install and can be used on 3.5 inch and 3.75 inch applications. You dont even have to measure to figure out what motor you have; the Bomb Proof Motor Mount Kit just works. Note: This product may cause more vibration than the OEM rubber mounts. This is the trade-off we make when going to stronger components.

 Applications:

 1979-1995 Pickup and 4Runner 4 Cylinder 22R, 22RE, 21R, 20R, 18R, 3.0L 3VZE V6, 2.7 3RZFE 4CYL, and 3.4L 5VZFE V6.

NOTE that these are second hand, they were working prior to being removed.

Please contact me to discuss and for a price.

If you are looking for some limit straps that won't break the bank, these are the ticket. Flexable, easy to install and great for those on a budget. Don't let the name fool you, they will work great for most people with lighter rigs like Suzuki's and Toyota's.

Limits suspension travel for vehicles with Coilovers, Air Shocks and Coils from overextending- causing damage to the shock and or suspension components. 

Industry Standard 1/2" Hole for Mounting, come in sizes from 12-32" as measured from center of hole to center of hole end to end.

Features:

-Abrasion Resistant Layer at End for Increased Tear Resistance

-Abrasion Resistant Loop for Increased Tear Resistance.

-Zinc Plated Ends for Corrosion Resistance.

-Double Sewn for High Strength. 

2.0" Factory Series Bump Stop - 2" by Fox (983-02-091)

SOLD INDIVIDUALLY

FOX Bump Stops were created to provide additional bottom out control to maximize the vehicles entire suspension travel. Developed in conjunction with top offroad racing teams to achieve ultimate performance within a compact and light package. The FOX bump stop can easily be setup for any conditions by removing the aluminum Schrader cap and adjusting the internal nitrogen gas pressure. The long lasting and replaceable Delrin pad insures quiet operation.

A new, innovative, never before seen product, our Longfield™ Studless Hubs set the bar in quality and performance. The Longfield™ Studless Hub replaces the weaker, prone-to-breaking locking hubs, hub gears, and hub studs by utilizing a stud-less hub design and inner locking puck. Chances are, if you were to break the studs in your hub, the threads would be damaged and the hub would need to be replaced. With the Longfield™ Studless Hubs, you will never again need to worry about your hubs, hub gears, and hub studs breaking on the trail.

The Longfield™ Studless Hub and Inner Locking Puck are both constructed out of chromoly steel for superior strength and quality. The Longfield™ Studless Hubs are stronger than the OEM locking hubs and are designed to handle even higher torque loads than our Creeper Drive Flanges. The Longfield™ Studless Hubs will also include a full set of front wheel bearings to replace your old, worn out bearings.

We are so confident with the quality and strength of our new, innovative Longfield™ Studless Hubs.

 Note: On 1979-1981 Toyota Pickups, you will need the following additional parts:

• IFS Vented Rotors (part #140332-1-KIT)
• Toyota IFS Calipers (140444-1-KIT, 1040445-1-KIT)
• IFS Caliper Brake Pads
• Front Wheel Studs

Note: These will lock your front axle into 4WD. To unlock your front axle, you will need to remove the locking puck.

Brand:Summit Racing

Manufacturer's Part Number:SUM-G1153

Part Type:Seat Brackets

Product Line:Summit Racing® Universal Sliding Seat Brackets

Summit Racing Part Number:SUM-G1153

Seat Bracket Style:Sliding

Bracket Color:Natural

Bracket Material:Steel

Quantity:Sold as a pair.

Notes:Dual locking design. NHRA compliant. One pair required per seat, must be used with the Summit fixed brackets for installation.

These Summit® universal sliding seat brackets give you a trouble-free way to install your new seats. They will bolt directly to your Summit® seats without modifications. Used along with our fixed brackets, you can mount your seat wherever you want inside your vehicle. They're manufactured from heavy gauge steel and come assembled and ready to bolt to your seat.

We put a lot of thought into our new Summit® Race seats--and it shows. For example, we gave them three separate belt openings instead of one, so you can use "H" or "Y" style safety harnesses. We also added two recessed locations, so you can anchor them to a roll bar. Other features include a lower "stance" for more head clearance, cone and rib back supports for added impact protection, and a ribbed mounting base for added strength. We also added more surface texture and cover beadlocks to keep the seat covers in place.

Finally a Toyota T case mount that can handle the abuse of rock crawling with the ultra low torque of dual cases is here. The TGHD T Case mount kit will totally eliminate any worries of a broken T case mount on the trail, or on the comp site. We are so confident in this product that it is offered with a world famous Lifetime No Questions Ask Warranty.

 The TGHD T case mount is stamped out of 1/4” thick steel plate, and then welded on a jig to ensure the best fit possible.

 These T case mount kits are coated with clear zinc (silver color) for a trick finish that will last a lifetime.

 The bushings are polyurethane for long lasting performance and durability.

 Can be used as a stock replacement on 4cyl T cases for applications from 1982-1995, or with our dual case cross-member and other popular dual case cross-members on all 1979-1995 applications. Note: This product may cause more vibration at high speed driving than with the OEM rubber mounts.

RCV

This is the ultimate upgrade for your factory Toyota Pickup & 4Runner solid axle factory Aisin/Asco hubs. These inner hub gear are completely made from 4340 alloy steel for increased torsional strength. Easy installation and warranted against breakage. These gears will fit the OEM CV joints as well as RCV Performance upgraded CV joints.

Fits: '79-'85 Toyota Pickup  & '84-'85 4Runner 

Please Note: These will not work with IFS Hubs.

Note: Sold as a pair.

TRAIL GEAR

Bigger tires mean more failure points, keep your rig running problem –free with Trail-Gear’s OEM replacement 1979-85 Toyota hub gears made entirely of 4340 chromoly. The TG Chromo Gears are so strong they will be able to handle all the abuse you put them through. The TG Chromo Hub Gears are a direct replacement that requires no modifications. Simply pop them in and drive with confidence. Purchase a complete set of four (1 pair inner gears and 1 pair outer gears) 

With 30 spline birfields, six stud knuckles, and chromo hub gears or drive flanges, the next weak link in your front axle is your hub studs. When they fail you will be left without four wheel drive, and often times the hub will be unrepairable. Trail-Gear, in partnership with ARP, have designed the most durable hub stud on the market. These hub studs are made from the strongest material ARP can manufacture for this type of fastener. ARP 2000 material has a tensile strength of 220,000 PSI and the ARP 2000 hub stud is cadmium plated to ensure that it is protected from rust and corrosion for many rough years to come. On the top of the stud we machined a 6mm hex head so that installation and maintenance is easy and no special tools are required. ARP 2000 hub studs are sold in kits of six with all the necessary hardware included.

Kit Includes:

•  (6) ARP 2000 Hub Studs

•  (6) Conical Washers

•  (6) Lock Washers

•  (6) Nuts

THESE ARE PRICED PER SIDE SO A QUANTITY OF 2 ARE NEEDED FOR ONE VEHICLE.

This is a replacement pinion seal.  This is a much better seal than the seals you find at your local parts store because usually they don't have the special dust shield lip.  These are really no different than a heavy duty seal other than they do not have an indexing lip for installation.  We usually coat the outside of these seals with a little RTV and then press them in.

Features:

-Special Lip for dust sealing- Just Like OEM.

There are sizes    29 Spline   and 27 Spline

Only for Toyota 8" diffs

Solid pinion spacers prevent loosening of the gear setup preload. Originally designed for older Toyota (solid axle) applications, Toyota stopped using them decades ago. Solid spacer and shims replace the crush sleeve. It takes a little longer to set up but you won't have to keep retorque the pinion nut down the road.

There are 2 sizes  

• 4 Cylinder
• V6 / High Pinion

 Note: Not designed for IFS vehicles

After years of development and testing, these knuckles and steering arms have set a new standard in Toyota knuckle strength and reliability. The Fully Loaded Six Shooter Kit totally eliminates the problem of broken steering knuckles and studs. The addition of two studs in each arm effectively prevents the steering arm from becoming loose or shearing off the studs under extreme loads. The knuckle housing was designed with thicker than stock material and larger gussets have been added around the outside of the knuckle for extra strength. Precision CNC machined, each set of knuckles and steering arms are inspected and tested for the highest quality of products that Trail-Gear can deliver.

Included in The Hilux/Pickup/4Runner Fully Loaded Six Shooter Kit is a special 6 hole shim pack for use between the top of the knuckle and the steering arm. Also included is a 1/2" coarse thread bolt to help remove the steering arms for knuckle service. To remove the steering arms, remove all 6 nuts, then install the bolt in the top of the arm. As the bolt is tightened, the steering arm is pulled up off the knuckle. Stock lower bearing plates and shims from your old knuckles are needed for knuckle assembly. A minimum of four additional steering arm studs are needed for installation. We think the Fully Loaded Six Shooter Kit is so bullet proof that we have given it our world famous no questions asked lifetime warranty.

NOTE: DOES NOT INCLUDE KNUCKLE STUDS AND HARDWARE, SOLD SEPARATELY

Can also use on 40 and 60 Series Landcruiser

Need an E-brake? Have bad cables, or a disk brake conversion? We have the answer with our simple and affordable Toyota T-case E-Brake Kit. It can be installed in under 1 hour and is fully bolt on. You do have to remove the t-case output flange in order to clearance the dust seal cover.

The E-brake kit reuses your stock e-brake cable up to the frame mounted e-brake arm located in front of your fuel tank. The t-case e-brake is constructed of laser cut and tig welded CNC formed 1/4 plate steel. Includes all parts you will need for installation, comes with instructions.

Fits all 4 cyl. Manual Toyota t-case's. Bracket’s are designed with a skid plate below the caliper and the ends are formed and tig welded to the main plate. The box style mount helps ensure no flexing of the t-case and caliper mount. This helps eliminate wear on the pads as well as possible stress on the t case itself. May not fit with all aftermarket t-case crossmembers.

Please note: 79-83 will require swapping to large 10mm bolt pattern flanges.  Due to many variations in Skid plates, transfer case combination,motor and trans mounts, fuel lines closest to rotor of t case e-brake may need to be relocated to clear. This is very common on 4 runners where the body is lower for rear passenger foot well. Depending on how much t case skid plate lifts the transfer case, trimming and boxing of floorboard may be required.

Instructions:

Installation of the t case e-brake requires you remove the t case output flange and remove the dust cover to fit rotor to back side of flange.

After removing flange and dust cover install rotor to back side of flange. We use the stock drive shaft bolts to position the rotor, the rotor is tapped for 2 patterns, determine the correct pattern for your drive shaft.

Next remove 4 bolts on the back transfer case cover, these are the bottom 2 and 2 above them. There is also a 5th bolt to remove on the far outside edge of the case, use the caliper mount to determine which one if unsure. This bolt will use the included spacer. Install t case flange with rotor, then slide caliper mount and caliper up to the rotor and install new longer bolts, flat washers and lock washer. Install jam nuts to all thread, then install yoke ends to all thread. Install arm to caliper mount, position of the arm will need to be determined by the installer as to which direction the arm will point and which holes to use. You may flip the arm and use the 3 adjustable yoke holes or use the standard single hole to install on the mount. Install 2.5 x 3/8ths bolt, flat washers and locknut. It is not necessary to tighten the lock nut completely, the arm should move freely but not be loose. Install the adjustable yoke ends with all thread and jam nuts. One end will use the spring to hold the pin, the other side will use the cotter pin. The shoulder bolt will fit through the stock e brake cable eye on the end of the e-brake arm. Note: 79-83 style cable will require a loop installed with wire crimp. Final adjustment may be needed and is the responsibility of the final installer.

1986 and later Hilux pickup trucks and 4Runner feature larger vented rotors from the factory. Earlier 1979-1985 trucks used solid (non vented) rotors up front along with smaller calipers. If your installing a solid front axle on an 86 and later rig you will want to install a set of these vented rotors onto the axle. With these rotors you will be able use your existing larger IFS calipers. Simply unbolt your existing rotors and replace them with these vented rotors. Slight grinding of the rotors backing plate will be needed. Then simply install the IFS calipers right on to the solid axle using the factory bolts. These rotors can also be used on 85 and older trucks to increase braking effectiveness. Fits 81-85 Solid axles with 8 hole style rotors.

Price is per rotor. You will need 2 to do one axle.

Solid one piece design. Features FJ80 tapered hole. One piece, forged design. Extra strong, wide design. Ideal for use with crossover steering. Flat arm, no drop.

These are usually used in buggies, or Suzuki Samurai's on FJ60 Steering Box's. Most people when doing standard high steer on a Toyota use the "stock drop" pitman arm.

Fits Toyota 4wd Steering Box's

Solid one piece design, which makes this pitman arm incredibly strong! Features FJ80 tapered hole. One piece, forged design. Extra beefy, wide design close to tie rod end hole. Ideal for use with crossover steering. Same drop as factory pitman arm. Why would you need this? IFS Steering box's have a tie rod incorporated into the pitman arm. In order to replace the tie rod end, you have to replace the pitman arm. For ultimate strength and longevity, high steer systems use an FJ80 tie rod end in the drag link, and have a tapered hole for the FJ80 end to go into such as in this pitman arm. We choose to do it this way rather than have an adapter to go to the factory pitman arm because most likely if you are using a used steering box, the pitman arm is worn out.

Toyota King Pin Bearings

When it comes to rebuilding front axles, some people insist on using only Japanese components. Always looking to give customers what they want, Low Range offers these bearings made by Koyo, NSK, NTN or Nachi. With 12 needle bearings in the cage distributing stress across 12 points of contact, these are a cut above others that may have fewer, larger needles. Larger needles in a cage doesn't necessarily mean it takes a higher stress load.

A cheaper option but still good quality are FAG Bearings.

Sold Individually.

Fits:

1979-1985 Toyota Hilux Pickup, 4Runner

1969- 1/91 Toyota Landcruiser FJ40,FJ55,FJ60,FJ62

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Will Fit the Following Models:

• 1969-1983 FJ40 front or rear
• FJ45 front or rear
• 1968-1979 FJ55 front or rear
• 1981-1987 FJ60 front or rear
• HJ60 front or rear
• 1988-1990 FJ62 front or rear
• BJ70 Leaf Srung Only (not coil sprung)
   
• 1990-1992 Landcruiser FJ80 Rear
• 1993-1997 Landcruiser FZJ80 Rear
• 1990-1997 Landcruiser HDJ80 Rear
• 1990-1997 Landcruiser HZJ80 Rear

Includes 1 Ring and Pinion Gear Set for one differential.

Toyota Pinion Flange Fit Kit Use When Upgrading to 29 Spline Pinion by Nitro (YOKTOYFITKIT-29) OR Trail Gear  (304110-1-KIT)

Replaces Toyota OE Part number 41204-35100 & 41204-35110.

NITRO Required to fit Nitro 29 Spline 8” or 9.5” Ring & Pinions to 2002 & older vehicles.In 2002, Toyota started using 29 Spline pinion & flange on the 8” & 9.5” differentials. Following Toyota's lead for an upgrade, Nitro Gear & Axle has been upgrading much of their line of Ring & Pinions for Toyota to 29 Spline. This means, if you are fitting the newer 29 Spline Ring & pinion to a 2002 or Older diff, you will need this flange.

There are 2 sizes of pinion flange nuts, 27 spline and the larger 29 spline

If you have a 2001 and Older Toyota Pickup then most likely your pinion flange is going to be 27 Spline unless it has been upgraded.   The easiest way to verify this is to count the splines on the pinion gear. If you want to run the new 29 Spline Ring and Pinions, you will need a new 29 Spline Pinion Flange, Seal and Nut. This is just the NUT, seal and flange are available elsewhere.

Low Range Off Road is your source for brand new solid axle spindles. New forged units are made to OEM Specs and CNC Machined to high tolerances. These spindles are great when building or rebuilding a Rock Assault Housing, a Diamond Axle,an OEM axle, and Ruffstuff Specialties housings. 

Comes with new Brass Bushing.

Sold individually. 

Note: For Extreme Duty Use, See the OEM Chromoly Replacement Spindle 

Great quality brake lines at low cost! These coated steel braided brake lines are 26" long and are DOT approved. They are made for the Toyota but work great when doing axle swaps.

Toyota Brake Line Kit (2 Front 1 Rear) 26" Long Extended-TB-LK3 (140011-1-KIT)

Toyota Brake Line Individual Rear (Female-Male)-TB-LR (140334-1-KIT)

Low Range Off Road is proud to give you options when it comes to drive line flanges. This one in particular is one of the only flanges that will work with early 1979-1983 small 8mm bolt pattern drive shafts. This fits the pinion side only and will fit stock ring and pinions and aftermarket ring and pinions with 27 splines.

Patterns Available:

56mm X 64mm Early 1979-1983 Toyota Hilux Pickup U-Joint (NON CV)
60mm X 60mm Late 1984-1995 Toyota Pickup and 4Runner U-Joint (NON CV)
66mm X 66mm 1995-2004 Toyota Tacoma, 1996-2002 4Runner, Toyota Tundra 2WD UJoint (NON CV) only with 27 spline.

While most V6 trucks came with 1" master cylinders, 1979-1995 4 cylinder Toyota Pickups and 4Runners got left with a 7/8" cylinder.

TB-MC-HILUX   Stock Cylinder Found on V6 Equipped Pickups

V6 Master Cylinders are a direct replacement for your 4CYL variant. With larger drums, or with larger calipers, you may be finding that the pedal wants to go all the way to the floor.   

This master cylinder may need slight readjustment of the brake lines.  It is good to note that the front hole is for the front brakes and the hole closest to the booster is for the rear brakes.

When Trail Gear tested the strength of 6 Stud knuckles, they found that running 6 OEM Studs on the 6 Stud knuckles was stronger than running 4 ARP Magnum Studs on a stock 4 stud knuckle.  So, with this information Trail-Gear looked at ways to make it stonger than even running OEM and not the cost of ARP studs. Now, Stronger and longer than stock Toyota replacement knuckle studs and more affordable than our Magnum Studs these studs will provide great strength without breaking the bank. Each stud is constructed from a proprietary metal made exclusively for Trail Gear.  These studs are manufactured to Trail-Gear's strict specifications and are significantly stronger than OEM standard (testing exceeded Class 12.9 standards). Trail Gear super metal knuckle studs are .250” (1/4”) longer than stock to accommodate all aftermarket steering arms. Like our Magnum Studs, TG super metal studs feature an integrated 8mm hex head for easy removal. These studs should be your first choice for knuckle hardware when repairing or upgrading your high-steer system.

We recommend using Locktight on the lower threads when installing knuckle studs. Studs should be tightened to 40 ft-lbs in the knuckles. Stud nuts should be tightened to 75 - 80 ft-lbs.

Fits 1979-1985 Toyota front solid axle knuckle.

NOTE: This is enough hardware to complete one six shooter knuckle. Purchase 2 kits for both knuckles.

Kit consist of the following:

• Knuckle cone washers (QTY: 6)
• Knuckle wave washers (QTY: 10)
• Knuckle nuts (QTY: 10)
• TG Super Metal knuckle studs (QTY: 10)

Tired of wiping big clumps of dirty sandy grease off of your knuckle balls after every trip? So are we. The engineering department at Trail Gear was asked to look at the problems with the OEM design along with what was currently offered on the market and they came up with a one-piece, high grade polyurethane seal that is durable and will give you a lifetime of dependability. Trail Safe Knuckle Ball Wiper Seals are without a doubt the best in the industry. No other design is comparable in performance and quality.

The Trail Safe Knuckle Ball Wiper Seal is a double sided seal that keeps grease in and dirt out, all while eliminating the use of the OEM felt and rubber. Since it is made from seal-grade polyurethane, not UHMW, the seal is pliable enough to stretch over the knuckle ball during installation. This eliminates the need to cut the seal for installation which allows water to enter the knuckle ball and for grease to escape. Trail Safe Knuckle Ball Wiper Seals are sold in pairs with the legendary Rock Rings.

One kit will complete one axle. Kit Includes:

• (2) Trail Safe Knuckle Ball Seal Wipers
• (1) Rock Ring Kit
• (16) Rock Ring Bolts
• (16) M6 Lock Washers