Menu
View cart
Close

Filters

VEHICLE

Toyota Pinion Flange Fit Kit For use when upgrading to 29 spline pinion Sold out

Toyota Pinion Flange Fit Kit For use when upgrading to 29 spline pinion

$0 NZD
from $175.00 NZD
Toyota Pinion Flange Fit Kit For use when upgrading to 29 spline pinion

Toyota Pinion Flange Fit Kit For use when upgrading to 29 spline pinion

by Nitro Gear
Sold out
$0 NZD
$225.00 NZD

Toyota Pinion Flange Fit Kit Use When Upgrading to 29 Spline Pinion by Nitro (YOKTOYFITKIT-29) OR Trail Gear  (304110-1-KIT)

Replaces Toyota OE Part number 41204-35100 & 41204-35110.

NITRO Required to fit Nitro 29 Spline 8” or 9.5” Ring & Pinions to 2002 & older vehicles.In 2002, Toyota started using 29 Spline pinion & flange on the 8” & 9.5” differentials. Following Toyota's lead for an upgrade, Nitro Gear & Axle has been upgrading much of their line of Ring & Pinions for Toyota to 29 Spline. This means, if you are fitting the newer 29 Spline Ring & pinion to a 2002 or Older diff, you will need this flange.

Differential: Toyota 8" & 9.5"
Pinion Spline Count: 29
Bolt Patterns: 60mm x 60mm, 66mm x 66mm
Seal Surface: 1.615"/41mm
Kit Includes:
  • Dual Drilled Pinion Flange
  • Pinion Nut
  • Pinion Seal

TRAIL GEAR  The 29-spline Differential Hardware kit contains all the 29-spline hardware needed to use 29-spline Ring & Pinon gears in your Toyota differential.  This kit includes our forged chromoly 29-spline Quadruple-drilled flange with preinstalled dust shield, 29-spline Trail-Safe Pinion Seal, and 29-spline pinion nut.  Fits 8” Toyota differentials with 29-spline pinion gears (Ring & Pinion gears sold separately). 


Included bolt patterns:  66mm x 66mm x 11mm, 60mm x 60mm x 10mm, 60mm x 68.3mm x 10mm, & 61.5mm x 70mm x 10mm.

Toyota Differential Solid Pinion Spacer

Toyota Differential Solid Pinion Spacer

$0 NZD
from $40.00 NZD
Toyota Differential Solid Pinion Spacer

Toyota Differential Solid Pinion Spacer

by 4wdstuff
$0 NZD
$80.00 NZD

Only for Toyota 8" diffs

Solid pinion spacers prevent loosening of the gear setup preload. Originally designed for older Toyota (solid axle) applications, Toyota stopped using them decades ago. Solid spacer and shims replace the crush sleeve. It takes a little longer to set up but you won't have to keep retorque the pinion nut down the road.

There are 2 sizes  

  • 4 Cylinder
  • V6 / High Pinion

 Note: Not designed for IFS vehicles

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears NITRO

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears NITRO

$0 NZD
$700.00 NZD
Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears NITRO

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears NITRO

by Nitro Gear
$0 NZD
$700.00 NZD

29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.

Toyota 8" V6 29 Spline Ring and Pinion NITRO

Toyota 8" V6 29 Spline Ring and Pinion NITRO

$0 NZD
from $625.00 NZD
Toyota 8" V6 29 Spline Ring and Pinion NITRO

Toyota 8" V6 29 Spline Ring and Pinion NITRO

by Nitro Gear
$0 NZD
$650.00 NZD

High performance Nitro Ring & Pinion gear set for Toyota V6 in a 29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

NOTE

 The spline on the Pinion for the flange is 29 Spline, if you have a 27 spline flange you will also need to purchase a 29 Spline Flange with Nut and Seal

Toyota Differential Pinion Seal For 27 and 29 Spline Flanges

Toyota Differential Pinion Seal For 27 and 29 Spline Flanges

$0 NZD
from $30.00 NZD
Toyota Differential Pinion Seal For 27 and 29 Spline Flanges

Toyota Differential Pinion Seal For 27 and 29 Spline Flanges

by LowRange
$0 NZD
$35.00 NZD

This is a replacement pinion seal.  This is a much better seal than the seals you find at your local parts store because usually they don't have the special dust shield lip.  These are really no different than a heavy duty seal other than they do not have an indexing lip for installation.  We usually coat the outside of these seals with a little RTV and then press them in.

Features:

-Special Lip for dust sealing- Just Like OEM.

There are sizes    29 Spline   and 27 Spline

Toyota 8" 27 Spline Ring and Pinion YUKON

Toyota 8" 27 Spline Ring and Pinion YUKON

$0 NZD
$390.00 NZD
Toyota 8" 27 Spline Ring and Pinion YUKON

Toyota 8" 27 Spline Ring and Pinion YUKON

by Yukon
$0 NZD
$390.00 NZD

High performance Yukon Ring & Pinion gear set for Toyota V6 in various ratios  27 Spline

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

Toyota Differential Setup Installation Bearing Kits

$0 NZD
from $300.00 NZD

Toyota Differential Setup Installation Bearing Kits

by Various
$0 NZD
$325.00 NZD

These Toyota Differential Setup Installation Bearing Kits include what you need to make your gear setup a breeze. Kit includes high quality bearings from manufacturers such as Koyo and Timken, crush sleeve, gear marking paint & brush, shims, and pinion seal.

8"  V6 and High Pinion

8"  4 Cylinder

9.5" Landcruiser

Toyota Triple Drilled Pinion 27 Spline Flange for Early and Late Patterns Sold out

Toyota Triple Drilled Pinion 27 Spline Flange for Early and Late Patterns

$0 NZD
$60.00 NZD
Toyota Triple Drilled Pinion 27 Spline Flange for Early and Late Patterns

Toyota Triple Drilled Pinion 27 Spline Flange for Early and Late Patterns

by LowRange
Sold out
$0 NZD
$60.00 NZD

Low Range Off Road is proud to give you options when it comes to drive line flanges. This one in particular is one of the only flanges that will work with early 1979-1983 small 8mm bolt pattern drive shafts. This fits the pinion side only and will fit stock ring and pinions and aftermarket ring and pinions with 27 splines.

Patterns Available:

56mm X 64mm Early 1979-1983 Toyota Hilux Pickup U-Joint (NON CV)
60mm X 60mm Late 1984-1995 Toyota Pickup and 4Runner U-Joint (NON CV)
66mm X 66mm 1995-2004 Toyota Tacoma, 1996-2002 4Runner, Toyota Tundra 2WD UJoint (NON CV) only with 27 spline.

Toyota Pinion Flange Nut

Toyota Pinion Flange Nut

$0 NZD
$10.00 NZD
Toyota Pinion Flange Nut

Toyota Pinion Flange Nut

by LowRange
$0 NZD
$10.00 NZD

There are 2 sizes of pinion flange nuts, 27 spline and the larger 29 spline

If you have a 2001 and Older Toyota Pickup then most likely your pinion flange is going to be 27 Spline unless it has been upgraded.   The easiest way to verify this is to count the splines on the pinion gear. If you want to run the new 29 Spline Ring and Pinions, you will need a new 29 Spline Pinion Flange, Seal and Nut. This is just the NUT, seal and flange are available elsewhere.

Differential: Toyota 8" & 9.5"

 

Sold out

Toyota 8" V6 27 and 29 Spline Ring and Pinion REVOLUTION GEAR

$0 NZD
$475.00 NZD

Toyota 8" V6 27 and 29 Spline Ring and Pinion REVOLUTION GEAR

by Revolution Gear
Sold out
$0 NZD
$475.00 NZD

Revolution Gear Toyota 8 inch  V6 4 gear sets are made from the highest quality steel and are precision heat treated to OEM specifications, making for the best aftermarket gears available. All Revolution Ring and Pinion sets are backed by an industry leading 2 Year Warranty against defects. Revolution Gear's precisely controlled manufacturing processes create a flawless setup, smooth operation and longer gear life. With products that have been Street, Off Road and Race proven, you can count on Revolution Gear and Axle products to be the most trusted in the aftermarket.

  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

NOTE   The spline on the Pinion for the flange is either 27 or 29 Spline.

REVT8-488-V6 Toyota 8 Inch 4.88 V6 27-Spline Ring and Pinion

REVT8-488-V6-29 Toy 8" 4.88 Ratio V6 29-Spline Ring and Pinion 

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears SIERRA

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears SIERRA

$0 NZD
$700.00 NZD
Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears SIERRA

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears SIERRA

by Sierra Gear & Axle
$0 NZD
$700.00 NZD

29 Spline

Ring & Pinion Gear Sets from Sierra Gear & Axle are reasonably priced and are the highest quality aftermarket gear sets available. Sierra Gear Ring & Pinion Gear sets are engineered and manufactured for easy setup, quiet operation and long trouble-free life.

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears REVOLUTION GEARS

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears REVOLUTION GEARS

$0 NZD
$700.00 NZD
Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears REVOLUTION GEARS

Toyota 8" Reverse Cut High Pinion Ring And Pinion Gears REVOLUTION GEARS

by Nitro Gear
$0 NZD
$700.00 NZD

27 Spline

Revolution Gear and Axle has been producing gear sets since 1984. Our ring and pinions are made from the highest quality steel and are precision heat treated to OEM specifications, making for the best aftermarket gears available. 

Toyota 8" V6 29 Spline Ring and Pinion SIERRA

Toyota 8" V6 29 Spline Ring and Pinion SIERRA

$0 NZD
$700.00 NZD
Toyota 8" V6 29 Spline Ring and Pinion SIERRA

Toyota 8" V6 29 Spline Ring and Pinion SIERRA

by Sierra Gear & Axle
$0 NZD
$700.00 NZD

Ring & Pinion Gear Sets from Sierra Gear & Axle are reasonably priced and are the highest quality aftermarket gear sets available. Sierra Gear Ring & Pinion Gear sets are engineered and manufactured for easy setup, quiet operation and long trouble-free life.

 The spline on the Pinion for the flange is 29 Spline, if you have a 27 spline flange you will also need to purchase a 29 Spline Flange with Nut and Seal