Toyota Pinion Flange Fit Kit Use When Upgrading to 29 Spline Pinion by Nitro (YOKTOYFITKIT-29) OR Trail Gear  (304110-1-KIT)

Replaces Toyota OE Part number 41204-35100 & 41204-35110.

NITRO Required to fit Nitro 29 Spline 8” or 9.5” Ring & Pinions to 2002 & older vehicles.In 2002, Toyota started using 29 Spline pinion & flange on the 8” & 9.5” differentials. Following Toyota's lead for an upgrade, Nitro Gear & Axle has been upgrading much of their line of Ring & Pinions for Toyota to 29 Spline. This means, if you are fitting the newer 29 Spline Ring & pinion to a 2002 or Older diff, you will need this flange.

29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.

High performance Nitro Ring & Pinion gear set for Toyota V6 in a 29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

NOTE

 The spline on the Pinion for the flange is 29 Spline, if you have a 27 spline flange you will also need to purchase a 29 Spline Flange with Nut and Seal

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Will Fit the Following Models:

• 1969-1983 FJ40 front or rear
• FJ45 front or rear
• 1968-1979 FJ55 front or rear
• 1981-1987 FJ60 front or rear
• HJ60 front or rear
• 1988-1990 FJ62 front or rear
• BJ70 Leaf Srung Only (not coil sprung)
   
• 1990-1992 Landcruiser FJ80 Rear
• 1993-1997 Landcruiser FZJ80 Rear
• 1990-1997 Landcruiser HDJ80 Rear
• 1990-1997 Landcruiser HZJ80 Rear

Includes 1 Ring and Pinion Gear Set for one differential.

This is a replacement pinion seal.  This is a much better seal than the seals you find at your local parts store because usually they don't have the special dust shield lip.  These are really no different than a heavy duty seal other than they do not have an indexing lip for installation.  We usually coat the outside of these seals with a little RTV and then press them in.

Features:

-Special Lip for dust sealing- Just Like OEM.

There are sizes    29 Spline   and 27 Spline

High performance Yukon Ring & Pinion gear set for Toyota V6 in various ratios  27 Spline

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

Low Range Off Road is proud to give you options when it comes to drive line flanges. This one in particular is one of the only flanges that will work with early 1979-1983 small 8mm bolt pattern drive shafts. This fits the pinion side only and will fit stock ring and pinions and aftermarket ring and pinions with 27 splines.

Patterns Available:

56mm X 64mm Early 1979-1983 Toyota Hilux Pickup U-Joint (NON CV)
60mm X 60mm Late 1984-1995 Toyota Pickup and 4Runner U-Joint (NON CV)
66mm X 66mm 1995-2004 Toyota Tacoma, 1996-2002 4Runner, Toyota Tundra 2WD UJoint (NON CV) only with 27 spline.

The ARB  Air Locker is one of the world’s most highly regarded traction aid. The ARB Air Locker is a driver controlled locking differential originally designed to give serious 4 wheelers the traction needed to combat extreme off road terrain. When extra traction is required, the driver activates the Air Locker via a convenient dash mounted switch. Pneumatic pressure supplied by an on board air compressor engages ARB’s patented locking mechanism within the Air Locker, thus preventing the wheels from turning independently. The Air Locker is deactivated by flicking a switch, returning the differential to normal. By far the most coveted locker in the world! Choose from front or rear lockers.

Models

RD132 Toyota 8 inch 4cyl, V6 and High Pinion FJ80 Air Locker

The RD132 Superceeds the RD23 in March of 2007.

If you have a 4cyl differential, late model 50.00mm [1.969"] id carrier Bearings must be used. (ARB Part No. 160116)

RD142 Toyota Land Cruiser 9.5" Air Locker Full Floating

Please Note: The RD142 is made for all 50mm carrier bearings. If you are installing an Air Locker into an earlier model Toyota with a 45mm differential carrier bearing inside diameter then you will need to use the higher rated later model 50mm bearings: Timken # 32010X-32010X or ARB # 160116. If your OE carrier bearings have an ID of 50mm, replace them with new bearings of the same type.

Toyota Land Cruiser 9.5" Differentials (12 Bolt Full Floating. What does this mean "Full Float"?  The axle shaft is splined on both ends, the axle shaft does not support the weight of the vehicle, the bearings do- therefore, the axle "Floats" inside the axle housing.)

Please Note, this will not fit FJ80 / LX450 Front as these are 8" high pinion reverse rotation differentials. 

This locker will not work with any of the semi float c-clip rear axles!

How do I tell if I have a full floating or semi floating rear axle?  If the wheel hub is flush with the wheel it is a semi floating rear axle. If it has a hub that sticks out past the wheel then it is a full floating rear axle.  

For ease of install and people who are on a budget, Powertrax Lockrights are hard to beat. Of course, selectable lockers such as ARB air lockers would be much more desirable, the Lockright lockers get the job done for a fraction of the cost. Many differentials have a set of spider gears which allow the outside tire to turn faster

Differential: Nissan H233B with 2 Pinion Carrier

Axle Spline Count: 31

Manufacturer: Richmond Gear/Powertrax

Part # 3210

Vehicle Applications:

• 1987-1998 Nissan Patrol GQ Y60 (Front)
• 1998-2009 Nissan Patrol GU Y61 (Front)
• 1987-1998 Nissan Safari (Front)
• 1988-1994 Ford Maverick (Front)
• 1978-1988 Nissan Patrol 160 MQ (Rear)

Features & Benefits:

•  Very easy installation as it fits inside of the stock open differential case
• No need to mess with ring & pinion set up in most cases
• Strong/Reliable
• Inexpensive price point

True Trac limited slip for Toyota 8" V6 Differential. 

The True Trac limited slip uses a worm-gear design to bias torque from one tire to the other, providing extremely smooth operation. Since there are no clutches in this unit, there are no parts to wear out and no need to run limited slip additive in your oil. 

Fits:

1988-1995 Toyota V6 Rear Differential

WILL NOT WORK ON FJ80 FRONT

Details

This is the Zip Air Locker for the Toyota 8" V6 Differential.

So you may ask, since it is cheaper than what we are used to, is it going to break?  Well, we can say this... the case is a forged chunk of 4320 chromoly to start.  

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. 

The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. 

Locker Includes:

-Carrier Bearings for V6 Model (50mm ID Bearing)

-Switch with front and rear covers (So you can use the locker in the front or the rear of your truck)

-Nylon Line

-Seal Housing

-Quick Connect Air Fittings and Associated Adapters

-Zip Ties for Nylon Hose Routing

-Installation Instructions and Service Manual by Yukon Gear

Manufacturer Part Number: YZLTV6-30

Fits:

-Toyota 8" V6, or Turbo 4cyl Style Differentials found in 1986-1995 Toyota Pickup, Hilux, and 4Runner. (50mm ID Bearings)

-1996-2009 4Runner 8" Rear Differential without elocker.

-2007-2009 FJ Cruiser 8" Rear Differential with 50mm ID Carrier Bearings without Elocker.

-Toyota FJ80 Front High Pinion 8" Differential without Elocker.

-Toyota Hilux Pickup 1985-1997 with 50mm ID Carrier Bearings.

-Will not fit 2010+ FJ Cruiser and 4Runner.

-Will not fit non-elocking Tacoma 8.4" or T100 Differential.

-Will not fit elocking carrier found in Tacoma, 4Runner or FJ Cruiser.

If you are not sure on the differential you have, measure the carrier bearing Inner dimension, the V6 models are 50mm ID.

For ease of install and people who are on a budget, Powertrax Lockrights are hard to beat. Of course, selectable lockers such as ARB air lockers would be much more desirable, the Lockright lockers get the job done for a fraction of the cost. Many differentials have a set of spider gears which allow the outside tire to turn faster

Powertrax Lock Right Locker

Differential: Nissan H233B with 4 Pinion Carrier (Not LSD Posi Case)

Axle Spline Count: 31 or 33

Manufacturer: Richmond Gear/Powertrax

Part # 3220

Tech Notes: This locker only suits standard open 4 pinion carrier case. It will not fit the LSD Positraction. The original side gears will get reused with this locker.

Features & Benefits:

Very easy installation as it fits inside of the stock open differential case

No need to mess with ring & pinion set up in most cases

Strong/Reliable

• 2000-2004 Nissan Xterra 6 cyl (Rear)
• 1998-2004 Nissan Frontier 6 cyl (Rear)
• 1998-2004 Nissan Navarra 6 cyl (Rear)
• 1996-2004 Nissan Pathfinder 6 cyl (Rear)
• 1987-1998 Nissan Patrol GQ Y60 (Rear)
• 1987-1998 Nissan Safari (Rear)
• 1988-1994 Ford Maverick (Rear)
• 1998-2009 Nissan Patrol GU Y61 (Rear)
• 2003-2006 Nissan Terrano II (Rear)
• 2003-2006 Nissan Mistral (Rear)
• 2003-2006 Ford Maverick (Rear)