Toyota Differential Solid Pinion Spacer

Only for Toyota 8" diffs

Solid pinion spacers prevent loosening of the gear setup preload. Originally designed for older Toyota (solid axle) applications, Toyota stopped using them decades ago. Solid spacer and shims replace the crush sleeve. It takes a little longer to set up but you won't have to keep retorque the pinion nut down the road.

There are 2 sizes  

  • 4 Cylinder
  • V6 / High Pinion

 Note: Not designed for IFS vehicles

Toyota Pinion Flange Fit Kit Use When Upgrading to 29 Spline Pinion by Nitro (YOKTOYFITKIT-29)

Replaces Toyota OE Part number 41204-35100 & 41204-35110.

Required to fit Nitro 29 Spline 8” or 9.5” Ring & Pinions to 2002 & older vehicles.


In 2002, Toyota started using 29 Spline pinion & flange on the 8” & 9.5” differentials. Following Toyota's lead for an upgrade, Nitro Gear & Axle has been upgrading much of their line of Ring & Pinions for Toyota to 29 Spline. This means, if you are fitting the newer 29 Spline Ring & pinion to a 2002 or Older diff, you will need this flange.

Differential: Toyota 8" & 9.5"
Pinion Spline Count: 29
Bolt Patterns: 60mm x 60mm, 66mm x 66mm
Seal Surface: 1.615"/41mm
Kit Includes:
  • Dual Drilled Pinion Flange
  • Pinion Nut
  • Pinion Seal
Stock Toyota inner axle seals are prone to failure from the beginning. They do a horrible job of sealing inbetween the factory inner axles and the axle housing itself. Why does this matter? The birfields are designed to have higher viscosity lubrication (not gear oil) When gear oil seeps past the factory inner axle seals, you have 2 things happen. 1. The Birfields can wear out quicker and 2. The oil seeps out the front axle housing because the wiper seals are meant to keep in the grease, not oil and keep out crud and debris. These axle seals fix the common problem at a great price.  They are incredibly worth the investment.

Tired of wiping big clumps of dirty sandy grease off of your knuckle balls after every trip? So are we. The engineering department at Trail Gear was asked to look at the problems with the OEM design along with what was currently offered on the market and they came up with a one-piece, high grade polyurethane seal that is durable and will give you a lifetime of dependability. Trail Safe Knuckle Ball Wiper Seals are without a doubt the best in the industry. No other design is comparable in performance and quality.

The Trail Safe Knuckle Ball Wiper Seal is a double sided seal that keeps grease in and dirt out, all while eliminating the use of the OEM felt and rubber. Since it is made from seal-grade polyurethane, not UHMW, the seal is pliable enough to stretch over the knuckle ball during installation. This eliminates the need to cut the seal for installation which allows water to enter the knuckle ball and for grease to escape. Trail Safe Knuckle Ball Wiper Seals are sold in pairs with the legendary Rock Rings.

One kit will complete one axle. Kit Includes:

  • (2) Trail Safe Knuckle Ball Seal Wipers
  • (1) Rock Ring Kit
  • (16) Rock Ring Bolts
  • (16) M6 Lock Washers
Toyota ARP 2000 Hub Stud Kit, for 1 Hub

With 30 spline birfields, six stud knuckles, and chromo hub gears or drive flanges, the next weak link in your front axle is your hub studs. When they fail you will be left without four wheel drive, and often times the hub will be unrepairable. Trail-Gear, in partnership with ARP, have designed the most durable hub stud on the market. These hub studs are made from the strongest material ARP can manufacture for this type of fastener. ARP 2000 material has a tensile strength of 220,000 PSI and the ARP 2000 hub stud is cadmium plated to ensure that it is protected from rust and corrosion for many rough years to come. On the top of the stud we machined a 6mm hex head so that installation and maintenance is easy and no special tools are required. ARP 2000 hub studs are sold in kits of six with all the necessary hardware included.

Kit Includes:

  •  (6) ARP 2000 Hub Studs
  •  (6) Conical Washers
  •  (6) Lock Washers
  •  (6) Nuts

THESE ARE PRICED PER SIDE SO A QUANTITY OF 2 ARE NEEDED FOR ONE VEHICLE.

29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.

When Trail Gear tested the strength of 6 Stud knuckles, they found that running 6 OEM Studs on the 6 Stud knuckles was stronger than running 4 ARP Magnum Studs on a stock 4 stud knuckle.  So, with this information Trail-Gear looked at ways to make it stonger than even running OEM and not the cost of ARP studs. Now, Stronger and longer than stock Toyota replacement knuckle studs and more affordable than our Magnum Studs these studs will provide great strength without breaking the bank. Each stud is constructed from a proprietary metal made exclusively for Trail Gear.  These studs are manufactured to Trail-Gear's strict specifications and are significantly stronger than OEM standard (testing exceeded Class 12.9 standards). Trail Gear super metal knuckle studs are .250” (1/4”) longer than stock to accommodate all aftermarket steering arms. Like our Magnum Studs, TG super metal studs feature an integrated 8mm hex head for easy removal. These studs should be your first choice for knuckle hardware when repairing or upgrading your high-steer system.

We recommend using Locktight on the lower threads when installing knuckle studs. Studs should be tightened to 40 ft-lbs in the knuckles. Stud nuts should be tightened to 75 - 80 ft-lbs.

Fits 1979-1985 Toyota front solid axle knuckle.

NOTE: This is enough hardware to complete one six shooter knuckle. Purchase 2 kits for both knuckles.

Kit consist of the following:

  • Knuckle cone washers (QTY: 6)
  • Knuckle wave washers (QTY: 10)
  • Knuckle nuts (QTY: 10)
  • TG Super Metal knuckle studs (QTY: 10)

After years of development and testing, these knuckles and steering arms have set a new standard in Toyota knuckle strength and reliability. The Fully Loaded Six Shooter Kit totally eliminates the problem of broken steering knuckles and studs. The addition of two studs in each arm effectively prevents the steering arm from becoming loose or shearing off the studs under extreme loads. The knuckle housing was designed with thicker than stock material and larger gussets have been added around the outside of the knuckle for extra strength. Precision CNC machined, each set of knuckles and steering arms are inspected and tested for the highest quality of products that Trail-Gear can deliver.

Included in The Hilux/Pickup/4Runner Fully Loaded Six Shooter Kit is a special 6 hole shim pack for use between the top of the knuckle and the steering arm. Also included is a 1/2" coarse thread bolt to help remove the steering arms for knuckle service. To remove the steering arms, remove all 6 nuts, then install the bolt in the top of the arm. As the bolt is tightened, the steering arm is pulled up off the knuckle. Stock lower bearing plates and shims from your old knuckles are needed for knuckle assembly. A minimum of four additional steering arm studs are needed for installation. We think the Fully Loaded Six Shooter Kit is so bullet proof that we have given it our world famous no questions asked lifetime warranty.

NOTE: DOES NOT INCLUDE KNUCKLE STUDS AND HARDWARE, SOLD SEPARATELY

Can also use on 40 and 60 Series Landcruiser

These Toyota Differential Setup Installation Bearing Kits include what you need to make your gear setup a breeze. Kit includes high quality bearings from manufacturers such as Koyo and Timken, crush sleeve, gear marking paint & brush, shims, and pinion seal.

8"  V6 and High Pinion

8"  4 Cylinder

9.5" Landcruiser

Toyota 8" V6 29 Spline Ring and Pinion NITRO

High performance Nitro Ring & Pinion gear set for Toyota V6 in a 29 Spline

Nitro Ring & pinions are made from the highest quality forgings using state-of-the-art CNC machining processes. Strict tolerences ensure precision fitment and hassle free installation. Computer controlled lapping processes result in an excellent contact pattern and a quiet running setup that will last.

Each new application is test fitted by real differential experts and put through stringent review process prior to being released. Nitro is hard at work developing new products that you demand.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

NOTE

 The spline on the Pinion for the flange is 29 Spline, if you have a 27 spline flange you will also need to purchase a 29 Spline Flange with Nut and Seal

In many cases, stock wheel bearing nuts and star washers can be used several times. However, with the increased maintenance required of an off road vehicle, these will need to be replaced. Trail-Gear now offers a Chromo Spindle Nut Kit that allows you to more easily service your axle and decreases your long term service costs. The Locking Nut and Washer have been CNC machined from 4130 Chromoly. The Nut has also been heat treated to Grade 8 standards. Kit comes with the hardware necessary for one axle.

Advantages over stock:

  • Stronger than stock. Made out of 4130 Chromoly.
  • Extends the life of your wheel bearings due to loose spindle nut and OEM lock washer.
  • Ease of installation.

This kit includes:

  • Thrust Washer (qty 2)
  • Spindle Locking Nut (qty2)
  • Spindle Locking Washer (qty 2)
  • Washer, M3 locking (qty 4)
  • M3-.05 Socket Head Cap Screw (qty 4)

NOTE: 1 KIT SERVICES 1 FULL AXLE

Longfield Toyota Studless Hubs by Trail-Gear

by Trail Gear
Sold out
$750.00

A new, innovative, never before seen product, our Longfield™ Studless Hubs set the bar in quality and performance. The Longfield™ Studless Hub replaces the weaker, prone-to-breaking locking hubs, hub gears, and hub studs by utilizing a stud-less hub design and inner locking puck. Chances are, if you were to break the studs in your hub, the threads would be damaged and the hub would need to be replaced. With the Longfield™ Studless Hubs, you will never again need to worry about your hubs, hub gears, and hub studs breaking on the trail.

The Longfield™ Studless Hub and Inner Locking Puck are both constructed out of chromoly steel for superior strength and quality. The Longfield™ Studless Hubs are stronger than the OEM locking hubs and are designed to handle even higher torque loads than our Creeper Drive Flanges. The Longfield™ Studless Hubs will also include a full set of front wheel bearings to replace your old, worn out bearings.

We are so confident with the quality and strength of our new, innovative Longfield™ Studless Hubs.

 Note: On 1979-1981 Toyota Pickups, you will need the following additional parts:

Note: These will lock your front axle into 4WD. To unlock your front axle, you will need to remove the locking puck.

 

Toyota 8" 27 Spline Ring and Pinion YUKON

High performance Yukon Ring & Pinion gear set for Toyota V6 in various ratios  27 Spline

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up.  Models w/ factory 3.07 & 4.88's have a different offset and will need a new dropout when changing ratio.

Great quality brake lines at low cost! These coated steel braided brake lines are 26" long and are DOT approved. They are made for the Toyota but work great when doing axle swaps.

Toyota Brake Line Kit (2 Front 1 Rear) 26" Long Extended-TB-LK3 (140011-1-KIT)

Toyota Brake Line Individual Rear (Female-Male)-TB-LR (140334-1-KIT)

Each Axle Kit now comes with RCV Made in the USA 4340 Inner hub gears absolutely FREE.

Now gun drilled with Grease Zerk for Easy Re-Greasing!!

 Manufactured in the U.S. using only high-strength chromoly materials, RCV Performance Ultimate 30 spline CV Axle set simply replaces your weak Toyota axle shafts with a new high-strength design. The factory axles were designed with 30 splines at the differential, and neck down to 27 Spline at the CV creating a common failure point. This axle set upgrades the weak 27 splines at the CV to a 300M 30 spline race eliminating the need to neck down the shaft.

Tests prove Ultimate CV Axles to be twice as strong as OEM shafts, and they're just as tough at a straight angle as they are at extreme angles. Even if you have big tires and big power there are no worries. Ultimate CV Axles are low maintenance and operate with a smoothness you can feel - whether off road or on the street.

Axle set includes right and left inner axle shafts & 2 pregreased CV joints. Black oxide coating is standard, We can accommodate custom length inner shafts as well if needed.

What makes these axles unique among any other axle set is that the inner race is made from 300M. You can tell that the race is 300M by a slight discoloration from the rest of the birfield. These are the only birfields that have this billet 300M race.

Please add in if needed any custom axle lengths are needed.

Includes:

Inner Axle Shaft -Long

Inner Axle Shaft -Short

2 - 4340 Chromoly and 300M RCV Birfields

2- Inner Hub Gears, 4340 Chromoly

Birfields come pre-greased. Always use moly based grease for CV Axles and Birfields.

 

Application: Toyota Pickup ('79-'85) & 4Runner ('84-'85). Includes right and left inner axles & 2 CV joints
OEM/RCV Inner Spline 30
OEM/RCV Outer Spline: 30
OEM CV Inner Spline: 27
RCV CV Inner Spline: 30 (300M Race)
OEM/RCV Right Inner Axle Length: 15.13"
OEM/RCV Left Inner Axle Length: 31.31"
Inner Hub Gears Included? Yes

Longfield FJ80 Gun Drilled 30-Spline 4340 Chromoly Super Set

The Longfield™ FJ80 Gun Drilled 30-Spline Birfields are made out of 100% chromoly and are precision polished to remove any imperfections that may cause stress risers. The internals of the birfield are also made from 4340 chromoly and are dual heat treated for superior strength. The birfield has a M8 grease zerk at the end of the stub shaft and is gun drilled through the center of the birfield to allow for grease to pass through the zerk fitting and into the internals. This will save you precious time by eliminating the need to disassemble your axle just to service your birfields.

The FJ80 Gun Drilled 30-Spline Birfields also have a shallow relief near the splines on the stub shaft known as a Machined Spline Saver. The Machined Spline Saver eliminates stress concentrations caused by grooving from the tool that makes the splines on the stub shaft. The stress concentration from the spline groove is a common failure point on birfield stub shafts. The stub shaft of the Birfield has dual snap ring grooves to accommodate FJ80s with short and long drive flanges.

The axle shafts are also made out of 4340 chromoly steel.

Included in this kit is a set of new FJ80 ABS Tone Rings. This will allow you to install the Longfield™ FJ80 Gun Drilled 30-Spline Super Set on both ABS and Non-ABS FJ80 applications. No other kit on the market can compare.

Note: Included is the FJ80 Extended Dust Caps for 1990-1993 models that use short drive flanges.

Specifications

  • Made out of 100% chromoly and are precision polished to remove any imperfections that may cause stress risers
  • Birfield housing is made out of forged 4340 chromoly steel
  • Internals of our Longfield™ birfields are made out of 4340 chromoly steel and then dual heat-treated for superior strength
  • Machined spline saver to eliminate stress concentrations from the spline groove
  • Gun drilled to create grease passage through the birfield
  • M8 grease zerk at the end of stub shaft for easy greasing of the birfield
  • The axle shafts are also made out of 4340 chromoly steel

1990-1997 Toyota Land Cruiser | Lexus LX450 Trail Safe FJ80 Knuckle Ball Wiper Seals by Trail Gear 

Trail-Safe™ FJ80 Knuckle Ball Wiper Seal Kit

The Trail-Safe™ FJ80 Knuckle Ball Wiper Seal is a double sided seal that keeps grease in and dirt out, all while eliminating the use of the OEM felt and rubber. Since it is made from seal-grade polyurethane, not UHMW, the seal is pliable enough to stretch over the knuckle ball during installation. This eliminates the need to cut the seal for installation which allows water to enter the knuckle ball and for grease to escape.

Trail-Safe™ FJ80 Knuckle Ball Wiper Seals are without a doubt the best in the industry. No other design is comparable in performance and quality.

Note:. Trail-Safe™ FJ80 Knuckle Ball Wiper Seals are sold in pairs and one kit will complete one front axle

Specifications:

  • Double sided seal
  • Eliminates the use of the OEM felt and rubber
  • Made from seal-grade polyurethane, not UHMW
  • Comes with all neccessary bolts for installation

Application Data

  • 1990-1997 Toyota Land Cruiser FJ80
  • 1995-1997 Lexus LX 450

 

Low Range Off Road is your source for brand new solid axle spindles. New forged units are made to OEM Specs and CNC Machined to high tolerances. These spindles are great when building or rebuilding a Rock Assault Housing, a Diamond Axle,an OEM axle, and Ruffstuff Specialties housings. 

Comes with new Brass Bushing.

Sold individually. 

Note: For Extreme Duty Use, See the OEM Chromoly Replacement Spindle 

Economy Double Limit Straps

Economy Double Limit Straps

by LowRange
$60.00

If you are looking for some limit straps that won't break the bank, these are the ticket. Flexable, easy to install and great for those on a budget. Don't let the name fool you, they will work great for most people with lighter rigs like Suzuki's and Toyota's.

Limits suspension travel for vehicles with Coilovers, Air Shocks and Coils from overextending- causing damage to the shock and or suspension components. 

Industry Standard 1/2" Hole for Mounting, come in sizes from 12-32" as measured from center of hole to center of hole end to end.

Features:

-Abrasion Resistant Layer at End for Increased Tear Resistance

-Abrasion Resistant Loop for Increased Tear Resistance.

-Zinc Plated Ends for Corrosion Resistance.

-Double Sewn for High Strength. 

Bomb Proof Motor Mounts

Bomb Proof Motor Mounts

by Trail Gear
$190.00

Anyone who has dual cases with 4.70 gears in their Toyota rock crawler has at one time or another broken an OEM rubber motor mount and heard the awful sound of their fan blades hitting their radiator. We have an answer for that problem, we call it the Bomb Proof Motor Mount Kit. We feel so confident about this product that we back it up with a world famous No Questions Asked Lifetime Warranty.

 

The base of the motor mount (frame side) is made out of 1/4 inch plate, while the surface plate that the motor sits on is made out of 3/8 inch material and has a class 10.9 bolt that is mechanically locked to the engine mount plate, not just threaded in. The bushings out of a high grade polyurethane for durability and years of dependability. The finish is a clear zinc plating that looks sharp and will last a lifetime. The mount holes are slotted so that the Bomb Proof Motor Mount Kit is easy to install and can be used on 3.5 inch and 3.75 inch applications. You dont even have to measure to figure out what motor you have; the Bomb Proof Motor Mount Kit just works. Note: This product may cause more vibration than the OEM rubber mounts. This is the trade-off we make when going to stronger components.

 Applications:

 1979-1995 Pickup and 4Runner 4 Cylinder 22R, 22RE, 21R, 20R, 18R, 3.0L 3VZE V6, 2.7 3RZFE 4CYL, and 3.4L 5VZFE V6.